Click here to see all results
DT 297 PV MK II, 250 ohms, for phantom power

DT 297 PV MK II, for phantom power

Made in Germany
Available at authorized resellers
Article Number: 721042

Headset with condenser microphone for on-air news and sports commentaries (optionally with limiter).

The headsets in this series dispose of a dynamic headphone transducer with a frequency response of 10 – 30,000 Hz and excellent isolation from ambient noise. The single cable is detachable, the ear cushions are replaceable. The pivoting gooseneck microphone- boom design, can be swivelled to work on the left or right side of the headset, or set to the upper position when not in use.

▲ NEW - Improvement of immunity against RFI (Radio Frequency Interference) caused by GSM, DECT, UMTS, Tetra etc.
▲ Good ambient noise attenuation
▲ High-quality condenser cardioid microphone for improved bass response and high gain-before-feedback
▲ Very high speech reproduction quality and excellent intelligibility
▲ NEW - Flexible, pivotable gooseneck for optimal positioning with elastical microphone suspension
▲ Lightweight, low profile design
▲ Single-sided, detachable cable
▲ NEW - Limiter (Optional)
▲ Powerful neodymium headphone system for excellent reproduction accuracy
▲ Optimised frequency response according to IRT (Institute for Radiotechnology in Munich) regulations
▲ Balanced sound impression
▲ Closed headphone
▲ Circumaural ear pads, advanced ear cushion system
▲ Adjustable, soft padded headband
▲ Service-friendly construction due to exchangeablitity of all parts
▲ Single-ear-version: DT 287

All DT 297 versions are supplied without connecting cable. Please order the appropriate connecting cable separately (see accessories).

* Required Fields


beyerdynamic GmbH & Co. KG
Theresienstr. 8
74072 Heilbronn - Germany

Questions regarding Orders, Payment & Delivery

Phone: +49 7131 617-444

Product Advice

Phone: +49 7131 617-440

Or contact us per e-mail!
proaudio @beyerdynamic .com

technical data

Transmission type   Wired
Headphone design (operating principle)   Closed
Headphone impedanceAlso known as nominal impedance. The impedance is the AC resistance of the coils of loudspeakers and headphones in ohms. Since impedance depends on the frequency, it is always specified at a frequency of one kilohertz.   250 ohms
Headphone frequency responseThe frequency response specifies the highest and lowest frequencies reproduced by the acoustic transducer of the headphones.   10 - 30.000 Hz
Nominal sound pressure levelThe acoustical level, the headphone transducer produces to an artificial ear (a measurement device, which simulates a human ear) with an input power of 1 mW (dB/mW @ 500 Hz).   100 dB SPL
Polar patternThe polar pattern is the preferred pick-up direction of the microphone. According to the shape of the corresponding measurement plot, there are omni-directional, cardioid, super-cardioid or hyper-cardioid as well as figure-of-eight patterns. for microphone   Cardioid
Transducer typeThe transducer system is designed as a dynamic moving coil microphone, as a ribbon microphone or as a condenser microphone. for microphone   Condenser - Cardioid
ConstructionSound coupling to the ear. A differentiation is made between supraaural headphones, circumaural headphones and in-ear headphones.   Circumaural (around the ear)
Cable & plug   Detachable cable – various connectors available
Net weight without packaging   276 g

Spec Sheet

accessories for DT 297 PV MK II, for phantom power

K 190.40 - 1,5 m
K 190.40 - 1,5 m

Connecting cable for DT 190- and 290 series with 3 pin XLR male and 6,35mm jack plug: K 190.40 - 1.5 m

K 190.40 - 1,5 m
K 190.00 - 1.5 m
K 190.00 - 1.5 m
Connecting cable for DT 190 and DT 200 series HEADSETS with free ends
K 190.00 - 1.5 m
WK 190.00
WK 190.00
Coiled connecting cable for DT 190 and DT 290 series with free ends
WK 190.00
WS 97
WS 97
Wind screen for DT 297, TG I56c/ 57c, TG D57c/ 58c, Opus 82/ 87/ 88
WS 97
K 190.00 - 3 m
K 190.00 - 3 m
Connecting cable for DT 190- and DT 200-series HEADSETS with free ends
K 190.00 - 3 m
K 190.40 - 3,0 m
K 190.40 - 3,0 m

Connecting cable for DT 190- and DT 290 series with 3 pin XLR male and 6,35mm jack plug: K 190.40

K 190.40 - 3,0 m


Spec Sheet

User Manual

Info material

For more downloads please refer to our Service section.


80 ohms
250 ohms
No limiter
Limiter at 99 dB

Find distributors